winny in water---perfected!

[dbol]

I now have made winny that is so pure that it can go through a 29pin.

It is the only one that I would safely say you can make higher volumes with...like 100cc or more.

winny 50mg/ml suspension
1 gram of winny powder
6ml peg 400
.45 filter
.22 filter - optional if you want to sterile filter your BW.
.6ml polysorbate 80
bacterialstatic water or (distilled water and 1%BA)
small pyrex beaker
glass stir rod
20cc vial sterilized without the stopper in place.
several 18gauge pins
1 10ml syringe - for peg/winny/ps80
1 20ml syringe - for BW

1. take 20ml syringe and draw up 15ml of BW- set aside
2. put beaker in frying pan and put on simmer.
3. add 4ml of the 6ml of peg400 to beaker
4. add .6ml of polysorbate 80 to the beaker.
5. weigh out 1 gram of powder.
6. add powder to beaker
7. stir powder with glass stir rod.
8. heat 5 minutes after it fully dissolves.
9 remove from heat for 7 minutes.
10 draw up solution with 10cc syringe and put a .45 filter on it with an 18 gauge needle on the end - leave capped.
11. read how much solution there is in the syringe - about 5.5ml
12 deduct 5.5ml from 20cc end volume to get 14.5ml of BW needed.
13. add BW to the sterile uncapped 20cc vial.
14. filter the solution into the BW slowly....count the drops. I went 15 drops then capped and shook at first because I was paranoid, by the end I was dropping 80 drops between capping and shaking.....aprox 1cc.
15. also, I decided to vary where the drops hit in the vial by circling the outer edge of the vial with the dropper as I dropped them in the BW- I didn't want them to land in the same spot.
16. If you do it right you should have to recap and shake at least 15 times before done - because of this make sure your hands are very clean before you start this step because you will inevitably touch part of the vial cap that fits inside the vial.
16. For added protection heat it in the oven for 20minutes at 250 degrees at the end but I didn't

There you have it.......
I know what you are thinking.....oh great another fucking recipe to try that I can waste more powder on.....I will bet my nuts that this will work everytime with higher volumes too.

[Skyefire]

Bro, that great except the part about contaminating your vial. Is there a way around that ?

[dbol]

I was thinking about that lat night and all I could come up with is to use an alchol wipe to put the stopper back on the vial with, or you could sterilize an instrument like pliers by soaking them in isopropyl alcohol for 30minutes and then baking them for 30minutes too.
not sure which would be more effective. I figure that if you bake it at the end and you hands are kept very clean (no oil) that you will be alright but it is a concern.
or you could set the cap face down on top of an alcohol wipe, and each time use a new one. It would be very easy then to pick it up by only touching the outer edges, It would probably work the best to still use a New sterilized pliers in conjunction with the wipes.
does that make you feel all warm and fuzzy in side.

Skyfire, get to work on this winny recipe. It is something that you have to see yourself.

I believe that in theory the same system should work for testbase too.

[newmass]

BUY sterilt surgeons gloves and use them

[dbol]

I guess you could also just use a sterile vial for the mix and then no recapping for the shake. you would just have to pull the vent every time you shake, alcohol wipe it and reinsert.

[Skyefire]

Originally posted by dbol
I guess you could also just use a sterile vial for the mix and then no recapping for the shake. you would just have to pull the vent every time you shake, alcohol wipe it and reinsert.

That would be better. But I can't use winny (bad back) and right know I can't lift so no riods. So it is going to be a while til I do any exparaments.

[dbol]

I would have to know more about your problem to advise you for sure but I can tell you that an appropriate workout would help you rehabilitate any problem you may have more than hinder its healing. Even slipped discs can be worked back in alignment with careful training. I know I have a c4 and L5 injury.
good luck.

[2hardcore]

Originally posted by dbol
16. For added protection heat it in the oven for 20minutes at 250 degrees at the end but I didn't

There you have it.......
I know what you are thinking.....oh great another fucking recipe to try that I can waste more powder on.....I will bet my nuts that this will work everytime with higher volumes too.

Just a thought on your last step here. I'd avoid heating the solution to 250 in an oven. I think the water would boil out for sure. what u guys think?

[BuffNuts]

What a pain in the ass to shake 15 times...and add drop by drop...why drop by drop? Why not squeezer the whole thing in.
I've learned that you gotta have the PEG real hot before adding the water. For some reason as the water hits the PEG it starts to boil and itmicronizes the winny..then shake the hell out of it...works awesome..try it

[Skyefire]

Originally posted by BuffNuts
What a pain in the ass to shake 15 times...and add drop by drop...why drop by drop? Why not squeezer the whole thing in.
I've learned that you gotta have the PEG real hot before adding the water. For some reason as the water hits the PEG it starts to boil and itmicronizes the winny..then shake the hell out of it...works awesome..try it

its the water that boils bro, be careful.

Dbol, just saw that but I am starting back lifting now, just needed to heal up.

[BuffNuts]

I know its the water....i meant when the water hits the PEG it (water) starts to boil.....and sometimes the winny solidifies and becoms a big rock at the bottom. No problem, just heat it back up..and shake it while its hot.....lol sounds like a rap song.....anyways make sure you got a firm grip on the stopper or it will pop off right in your face...then vent it by jabbing A needle in it or slowly lift the stopper...ur choice

[kojie]

the ps80 isn't needed