Converting the new Revalor 200 into Tren Ace

[rado]

Alright so second attempt around and still not quite right. Here is what I did step by step using two cartridges of revalor-200 (4gram).

1.) I used heet to dissolve the crushed pellets (3 hours), then filtered through coffee filter.
2.) I poured in dissolved naoh (30mg since I was told 75mg per five cartridges and I only used two) and let it sit for 1 hour exactly.
3.) Ice cold distilled water and dripped for roughly 30 minutes (~400ml).
4.) Filtered through coffee filter and rinsed with a gallon and half of distilled water.
5.) Air dried for two days and used a card to chop up the powder.
6.) I weighed the dried powder and came out to almost exactly 3.5 gram (I used two cartridges which is a total of 4 grams).
7.) I mixed 1ml BA, 1ml EO, and 30ml GSO to get roughly 100mg/ml.
8.) Problem...the powder is not fully dissolving into the oil. I tried heating it ~225F for 30 minutes and it still isn't dissolving.

It looked like this:


I then filtered that through another coffee filter and there was a lot of goop left over but the filtered oil looked good. I went ahead and filtered that through a .2 syringe filter and ended up with this:



I scraped the goop off the coffee filter into a beaker and added straight EO just to see if it will dissolve...even sitting overnight is hasn't fully dissolved:


Can't figure out what I'm doing wrong...:(

Not sure you let it it dry completely, that's crucial. And it doesn't disolve completely either.

[short2stop]

Just finished conversion but the crystals aren't exactly crystals. More like a thick glue/gel. Theyve been drying over 24 hrs. Should I let them dry more or did I do something wrong?

[Jkap19]

Just finished conversion but the crystals aren't exactly crystals. More like a thick glue/gel. Theyve been drying over 24 hrs. Should I let them dry more or did I do something wrong?

Post up everything you did step by step.

[short2stop]

I don't have pictures but here's what I did (very similar to what everyone has said in this thread)

Crushed 5 carts
Dissolved in one bottle of heet for 2.5 hrs
Filtered gunk out at bottom
Added solution of 75mgs NaOH solution. Which turned to a solid and went to the bottom
Let the solution sit 1 hr then dripped Distilled water in for 40 min
Then filtered with a painters hat and washed with 2 gallons

One question I have is if it is normal to take 2.5 hrs to wash 2 gallons. It took me that long but it didn't seem right

[Jkap19]

First, you are suppose to use 750mg or.75g naoh per 5 carts not 75mg. How did you even measure that? I can't remember how long it took to drip 2 gallons of water on sumo but it was a while. I don't believe it made a diference. Have you made it into a solution yet?

[short2stop]

750mgs* yes. I have a scale. And I am currently doing that right now. It's sitting in a pot of hot water to speed up the process. Well see how it turns. Everything was going well until the last step. I also didn't put it on a plate to dry. I left it in the hat and that was a huge mistake. I can't get all the tren out. Live and learn. This is a lot different than the easy fina conversion I'm used to

[Jkap19]

750mgs* yes. I have a scale. And I am currently doing that right now. It's sitting in a pot of hot water to speed up the process. Well see how it turns. Everything was going well until the last step. I also didn't put it on a plate to dry. I left it in the hat and that was a huge mistake. I can't get all the tren out. Live and learn. This is a lot different than the easy fina conversion I'm used to

Did you drip the water? If so 2 gallons will take some time. Tip: next time make sure the water is very cold. Stick it in the freezer before you do the drip. This will give you larger crystals and therefore a greater yield.

Make sure to let me know how everything goes!

[rado]

Did you drip the water? If so 2 gallons will take some time. Tip: next time make sure the water is very cold. Stick it in the freezer before you do the drip. This will give you larger crystals and therefore a greater yield.

Make sure to let me know how everything goes!

Hence why the dripping should be done in the refrigerator.

[rado]

750mgs* yes. I have a scale. And I am currently doing that right now. It's sitting in a pot of hot water to speed up the process. Well see how it turns. Everything was going well until the last step. I also didn't put it on a plate to dry. I left it in the hat and that was a huge mistake. I can't get all the tren out. Live and learn. This is a lot different than the easy fina conversion I'm used to

this process takes patience, which seems most of you lack. But I've been there myself in the beginning. All of this process takes time, not like the old conversion; correct:thumb:

[Jkap19]

this process takes patience, which seems most of you lack. But I've been there myself in the beginning. All of this process takes time, not like the old conversion; correct:thumb:

Do you feel like your tren from revalor is more effective than ugl?

[rado]

Do you feel like your tren from revalor is more effective than ugl?

Hard to confirm that because I've gotten great results from both....the ONLY difference is that I know how mine was made....but I also trust my source 100%...

[short2stop]

So not taking it out of the filter at the end and letting it dry in there was my huge mistake because I just did another try and took it out of the filter and put it on a cookie sheet and if went perfect. I set it on a radiator and it dryed quickly too.
I also salvaged what I could from the first try and it mixed with the oil normally so the process worked. Thanks y'all

[Jkap19]

So not taking it out of the filter at the end and letting it dry in there was my huge mistake because I just did another try and took it out of the filter and put it on a cookie sheet and if went perfect. I set it on a radiator and it dryed quickly too.
I also salvaged what I could from the first try and it mixed with the oil normally so the process worked. Thanks y'all

What was your final yeild?

[short2stop]

Not very good... Low... But I'll try again and see if I do better. Do y'all add the BB and BA before or after you dissolve the tren in the oil

[Jkap19]

Add it before. I dissolve everything in ba/bb before adding oil.